Borrow APR vs supply APR: where utilization shifts the balance
How DeFi lending interest rates are determined: utilization and reserve settings set borrowing APR, while suppliers receive a share after the reserve factor.
By The Blocktide Editors4 min read
For borrowers and suppliers comparing a pool, DeFi lending interest rates are set by each market’s utilization curve and reserve parameters, then allocated between borrowers and suppliers.
Utilization and reserve settings set the quoted rates
A lending market calculates its borrowing rate from available liquidity, outstanding debt and a rate model configured for that asset. Utilization measures how much of the available pool is borrowed; as borrowing rises, utilization rises, too.
- Reserve balances show supplied liquidity and outstanding borrowing.
- The rate curve maps utilization to a borrowing APR.
- The reserve factor assigns part of borrower interest to the protocol.
The model connects these parts: it uses utilization and configured parameters to set the borrowing rate, then allocates the interest paid by borrowers across suppliers and the reserve. More borrowing against a fixed supply usually pushes utilization up and rates higher, balancing demand for loans against the liquidity left for withdrawals.
Many markets use a kinked curve. Below a configured target, the borrowing rate rises along a gentler slope; above the target, it rises faster to make borrowing less attractive and encourage repayment or new supply. The target and slopes vary by reserve, so identical utilization levels can produce different rates in different markets.
Aave V3’s interest rate strategy documents a two-slope utilization curve with reserve-specific parameters, including a base rate, an optimal usage ratio and two slopes. That makes Aave a useful reference for how a kink changes the rate path; the configured values determine where the kink sits and how sharply rates move after it.
Governance anchors and utilization jointly shape borrowing cost
A governance-set rate anchor can establish a reference point on a curve, while current utilization determines the rate around that point. In the DAI and USDS markets described in its borrowing information, SparkLend anchors the rate at the curve’s 80% utilization kink to a source set through Sky Governance; utilization then moves the actual rate around the anchor. Other assets use variable rates based on supply and demand. Spark’s explanation of borrowing rates sets out that distinction.
Take a simplified reserve at 80% utilization with a 6% borrowing APR and a 10% reserve factor. The supplier APR is approximately 6% × 0.80 × (1 − 0.10), or 4.32%. Only 80 cents of each dollar supplied is earning borrower interest in this illustration, and 10% of that interest goes to the reserve. The remaining share is spread over supplied capital.
This calculation helps compare the quoted borrower APR with the supplier APR: they measure different sides of the same pool. Actual protocols may account for additional reserve details, so treat the formula as a simplified estimate rather than a universal contract calculation. At SparkLend, checking the reserve’s current model and parameters shows how its configured anchor and utilization combine; SparkLend adds background on the lending market behind those rate settings.
Now change the example slightly: utilization moves above the 80% kink while the reserve’s configured parameters stay the same. The borrowing APR rises along the steeper section of the curve, so the supplier APR estimate rises through both higher utilization and the increased borrower rate. The anchor still informs the curve at the kink, but it does not freeze the rate above it. The allocation principle still holds: supplier interest depends on borrower interest, utilization and the reserve factor.
Separate base interest from token incentives when assessing yield. A displayed incentive can add to a supplier’s realized return, but it is distinct from interest paid by borrowers and can change on its own. For a borrower, the quoted APR is a snapshot: with a variable rate, realized cost follows the rate path over the time the debt remains open. Utilization shifts, parameter changes and the duration of the loan all matter.
Related
DeFi lending APR vs APY
APR annualizes interest without assuming compounding; APY includes an assumed compounding schedule. Compare like with like, and check the compounding assumption before treating two displayed rates as equivalent.
Can high lending yield reduce withdrawal liquidity?
Yes. High utilization can raise supplier yields while leaving less liquidity immediately available for withdrawals. A higher displayed rate therefore comes with a liquidity trade-off: check utilization alongside the yield before deciding how much liquidity to rely on.
To repeat the analysis, note the reserve’s utilization, kink, rate anchor, borrowing APR and reserve factor together. That quick check explains what moved and helps avoid treating an incentive, an APY and a variable borrowing APR as the same rate.